船用凸轮-挺柱副摩擦润滑性能研究  

Friction and Lubrication Performance of Marine Cam-Tappet Pair

作　　者：华德良 史修江 孙文 冯彦 卢熙群[1] HUA Deliang;SHI Xiujiang;SUN Wen;FENG Yan;LU Xiqun(College of Power and Energy Engineering,Harbin Engineering University,Heilongjiang Harbin 150001,China)

机构地区：[1]哈尔滨工程大学动力与能源工程学院,黑龙江哈尔滨150001

出　　处：《摩擦学学报》2022年第5期913-924,共12页Tribology

基　　金：中央高校基础研究项目(3072021CF0304)资助。

摘　　要：随着船舶柴油机功率密度和转速等性能参数的不断提升,配气凸轮-挺柱副面临着更加严苛的工作环境,尤其是界面微观接触区的摩擦学特性,在瞬态载荷冲击、速度冲击、曲率变化及局部粗糙峰接触条件下,界面摩擦及闪温迅速突变,带来磨损和胶合等表面失效问题.本研究中基于先进三维线接触混合润滑模型,考虑凸轮-挺柱副瞬态突变工况及几何变化、瞬态表面粗糙度影响以及润滑油非牛顿流体作用,采用稳定性好、收敛速度快的准系统数值分析方法开展凸轮-挺柱副摩擦闪温分析,揭示粗糙度参数、工况改变及几何结构对其润滑状态和摩擦闪温特性的影响规律,为船舶柴油机配气凸轮-挺柱副摩擦学优化设计及磨损胶合失效预测提供理论指导.With the continuous improvement of power density,speed and other performance parameters of marine diesel engine,the cam-tappet pair is facing more severe working environment,especially the tribological characteristics of micro-contact area at tribo-interface,under the conditions of transient load impact,velocity impact,curvature change and local rough peak contact,interface friction and flash temperature change rapidly,which produce surface failure problems,e.g.wear and gluing.Based on the elastohydrodynamic lubrication analysis model and the fast-moving heat model with consideration on the effect of the transient condition and geometric change,transient surface roughness of cam-tappet pair and the non Newtonian fluid of lubricating oil,the quasi system numerical analysis method with better stability and fast convergence speed was used to analyze the friction and lubrication performance of cam-tappet pair.The classical fitting formula was used to verify the correctness of our method.It was assumed that the surfaces of cam and tappet had sinusoidal ripple,and the effects of sinusoidal wave amplitude,base circle radius and cam speed on friction lubrication state were discussed.The results showed that during the operation cycle,the cam-tappet pair was affected by the surface roughness,resulting in drastic changes in the film state.In specific,the minimum film thickness decreased,the maximum film pressure increased,the friction coefficient and surface flash temperature rise increased significantly,resulting in the decrease of the film bearing capacity and lubrication failure easily,which was also the cause of wear and gluing failure of the tappet.When the base circle radius decreased,the slide-roll ratio of the surfaces increased,resulting in the drastic change of the slide-roll state and the increase of the surface flash temperature.Increasing the base circle radius reduced the maximum temperature rise of cam and tappet surface by about 10 ℃ and 20 ℃,respectively.The friction coefficient decreased,so increasing

关 键 词：船用柴油机 凸轮-挺柱副 混合润滑 摩擦系数 表面闪温 

分 类 号：TH117.1[机械工程—机械设计及理论] TH117.2